Horario de atención y direcciones de las tiendas

Epoxy Resins

EpoxiLay 102 -Epoxi para laminados-

EpoxiLay 102 -Epoxi para laminados-

Epoxy resin for unfilled laminates.
Low viscosity and odorless.
Neutral color, ideal for Carbon and Reinforcement fabrics.
Perfect for FX molds.

More details...

Kit de 1,16 Kg.

32,00 €

tax excl.

Add to wishlist

You must be logged

EpoxAmite® 102 is an easy-to-use liquid epoxy system formulated for a wide variety of fabrication applications. EpoxAmite® 102 includes the EpoxAmite® 100 Base and the EpoxAmite® 102 MEDIUM Hardener.  EpoxAmite® 102 is unfilled, low in viscosity, odorless and cures at room temperature. Cured epoxy displays exceptional physical and performance properties. It can be sanded, shaped, machined, drilled, tapped and painted.

EpoxAmite® 102 can be used with reinforcements such as S-Glass, E-Glass, Kevlar and Carbon fibers for lay-up applications or composite parts. EpoxAmite® 102 can also be mixed with fillers such as fumed silica for gel coat applications. Urefil® 3, Urefil® 7 and other fillers can be added for fairing, filleting or bonding applications.

Applications: Wet Lay-Up Lamination, General Bonding & Repair, Clear Coating - Gel Coating, Barrier Coating, Thin-Section Casting, Water Proofing, Patching & Small Laminates 

Also available: EpoxAmite® 101 FAST SET and EpoxAmite® 103 SLOW SET 

Preparation – Avoid breathing fumes - use in a well ventilated area at minimum. NIOSH approved respirator is recommended. Wear safety glasses, long sleeves and rubber gloves to minimize skin contact. This material has a high exotherm (generates heat). Do not mix components in glass or foam containers.

Materials should be stored and used in a room temperature environment (73°F/23°C). Elevated temperatures will reduce Pot Life. EpoxAmite® 100 Resin and 102 Hardener must be properly measured and thoroughly mixed to achieve full, high-strength, solid-cure properties.

Applying A Release Agent – For releasing epoxy from non-porous surfaces such as resin, metal, glass etc., use Ease Release 200 or 205 (available from Smooth-On) to prevent adhesion.

Measuring / Dispensing – Accurate ratio measurements by volume or weight are required for the material to cure properly and develop full physical properties. Refer to specified Mix Ratios in Handling Properties for proper measurements. Dispense Parts A and B proper proportions into clean plastic, metal or wax-free paper containers.

Adding Color - EpoxAmite® 102 can be colored with SO Strong® color tints (from Smooth-On). Pre-mix tint with Part A thoroughly and then add Part B.

Mixing – Be sure mixing utensils are clean and free of any potential contaminants such as dirt, dust or grease. Mix Parts A and B thoroughly for at least 3 minutes with a square edged mixing stick. Be aggressive and scrape sides and bottom of mixing container several times. Use the square edge of mixing stick to bring material off of the sides of container and blend. If using a drill mixer, follow with hand mixing as directed above to ensure thorough mixing. NOTE: If mixture is to be used for coating, pour into a roller pan to extend Pot Life.

Adding Fillers - A variety of dry fillers can be added. Pre-mix dry filler with Part A before adding Part B.

Important - Mixed EpoxAmite® 100 Resin with EpoxAmite® 102 Hardener is exothermic, meaning it generates heat. A concentrated mass of mixed epoxy in a confined area such as a mixing container can generate enough heat to melt a plastic cup, burn skin or ignite combustible materials if left to stand for its full Pot Life. Do not use foam or glass mixing containers or pour sections thicker than 1/8” (0.32 cm). If a batch of mixed epoxy begins to exotherm, move it to an open air environment.

No customer reviews for the moment.

Write your review

EpoxiLay 102 -Epoxi para laminados-

EpoxiLay 102 -Epoxi para laminados-

Epoxy resin for unfilled laminates.
Low viscosity and odorless.
Neutral color, ideal for Carbon and Reinforcement fabrics.
Perfect for FX molds.

Write your review

Customers who bought this product also bought :

AC-1 Pure Acetone

AC-1 Pure...

2,50 €

Paletina / Special Brush for Laminates.

Paletina /...

0,90 €

Fiberglass Mat 300 grm.


3,90 €

Epofer EX401 + E 416

Epofer EX401...

20,80 €